Your driver and many others have an external "current sense resistor" (some have internal sensors) , why not use them?

@tlfong01 : the DRV8801 supports external sense resistor (and I'm using one). Even beter, it has the "VPROPI" pin acting as amplifier, in order to be able to use a small resistor while getting decent voltage (specially usefull in a battery powered project like mine, where I don't want to loose 1V out of 12 in a sense resistor)

(1) My apologies for not reading your question carefully and giving you a silly answer. I read your question again and found that you presented your situation very well. (2) I am curious about your cave exploration robot project. It would be nice if your can show us the robot's user requirement or spec. (3) I guess you are using DC motors in your project. I happen to be playing with a robot car project, an 4WD/8WD with TMC2160 stepping motor (can also do DC motor) driver (big current > 10A). If I know your motor requirement better, I might suggest BLDC or stepping motors.

@tlfong01 : I have ni idea how to give a complete "description" of my robot on this site without being out of topic (If you have, it might be usefull to refer to it as most of my questions relate to this robot). Or if you are just currious, we could do a skype. For short, it's a robot to explore vertical narrow cracks, by driving blocked between the 2 opposit walls. Basicaly, the robot is made of 8 arms (2 horrizental "X") with a wheel at the end of each arm. Each wheel is pushed agains the wall (to avoid the robot slipping down) by a motor (those I'm asking about) pulling some elastic band.

The motors are very small geared DC motors (<1A, weigting less than 20g). The weight is a very important factor for this robot, as the force needed for the arms (ie motor torque) is proportionnal to the weight of the robot. The goal of torque control is to ensure constant force against the walls (ie "constant torque" changing a bit depending on the position of the arms)

(4) Are you using small DC motors such as N20 (see Ref below). Perhaps you can give me the link to your motor. (5) You following spec is good: "a robot to explore vertical narrow cracks, by driving blocked between the 2 opposite walls. (6) Is there are reason using drv8801, and not the possibly improved version drv8833/8871 (also see refs below). (7) The tmc2160/2209 has some advanced features on torque/current (using microstepping/pwm constant current) which might give you some brainstorming ideas. (8) You might also to consider BTN7971B, whose current sensing comparing with drv88xx.

Our discussion is getting TLDR, so let us do our long winded in this chat room.

References to motor drivers with different mot coil current sensing features.

Above references contain typos. It is too late for me to do editing. So I am sending an update.

Question: How narrow is your vertical narrow cracks, 18 inches, like below?

I found the above EESE question on drv8833 with Rpi Pico. The OP does not know his motor spec. So perhaps I can use the small N20 motor and experiment with. You can, on your side, try your STM32 your motor and can do sort of pair programming/development.

@Sandro Yes, the "vpropi" pin is good because it save power. The "sleep" pin also saves power. The "fault"pin perhaps also good because it it can warn over current which might mean load/torque over limit, but not sure. I vaguely remember btn7971b has similar current/sensing/fault features, but I have not used it.

For the DRV8833, it would also do, but I would need softPWM or some external logic in order to use it with a single harware PWM. And it is nearly 5 times the price of the DRV8801, so even if I need 2 times less, it's also more expensive

For the DRV8871, it doesn't support external sense resistor (it does internal measurement but without outputing it). It has a I limit pin, that is made to put a fixed current limit (it should be possible to trick it by applying a voltage or current to this pin instead of using a fixed resistor).

I do not know for the DRV8871, but the DRV8870 that I used on the first prototype (at first glance, it seems the same excepted that it uses an external sense resistor) does very poor job on current control when the motor is stalled.

Just above : the current state of the prototype

Ah, your cave robot looks interesting. I never thought of something like this before. Long time ago I read about window plane crawler robots for cleaning windows, but that is using a different method.

Now some random brainstorming comments:

N20 is a good choice, I learned many things from Polulu, but I bought the motors from TaoBao. Below is a reference of my learning notes.

My N20 has rotary encoder. My 8WD is for rough terrain. I am experimenting with different strategies, including the following. (1) All 8 wheels with speed encoder are moving at the same speed, perhaps same PWM frequency and duty cycle. If one wheel suddenly moves very fast, that means it is hanging in the air, perhaps above a hole or something, so no load no torque. But I am only thinking, no tests yet. The thing is that I don't measure motor coil current, to deduce torque.

Motor current sudden increase means stalled or jammed.

The other reason is that I am trying the driver in "chopper mode", or constant current mode. You might skimmed that following references for a rough idea of "current chopping".

There you are - Chopper Mode (Ref 3).

Yes, tmc2160 or tmc2130 is very complicated, using SPI/UART control. But tmc2130 without the external mosfet switches is very small, not bigger than drv8833.

Ah, I never knew that drv8801 is 5 times cheaper than drv8833, because I am only doing one off prototyping, hoping to learn some new stuff. If one day I am going to make perhaps 500 robots to make some money, of course I will components as cheap as possible, so to make as big money as possible. :)

I am using Rpi Pico because it is cheap (US$4), and it has a lot of PWM pins, and also two ADC pins, so is good for testing, not to worry it falling down a cliff or a cave.

Ah, almost bed time. So see you over the weekend. Cheers.

Why all those resources about stepper motors? (Excepted if you know a stepper motor the size of a N20?!?)

For the tmc2130, it has just 2 input pins in total (step + dir), so it can't be used for 2 DC-motors

For the prices of drv8801 vs drv8871, it seems I was "wrong" : it is just JLCPCB that incrased the price of the 8871 (probably because they are currently hard to come by currently). On digikey, they are about the same price, but 8871 is out of stock